Practical guide

Clean Smart Feed: Conveyor, Crumb Catcher and Reassembly

Unplug and empty Smart Feed, remove the named parts, keep its base dry and hand-wash the conveyor and crumb catcher. Align the belt lip and close the actual latch before restoring the food plan.

Owners following the instructions for their actual PetSafe feeder and current app · 4 minute read · Published

Unplug and empty before removing the food path

Current PetSafe cleaning support begins by unplugging and emptying a Smart Feed that is in use. Keep the food and due meal with your existing feeding arrangements while cleaning; a maintenance operation does not itself provide that meal. [1]

Remove the lid, unlatch the hopper from both sides of the base and lift the hopper away. The source then says to pull the conveyor’s red latch toward the back to an upright position, lift the conveyor out and remove the crumb catcher from its underside.

These are the manufacturer’s named removable components. They do not authorize opening the electronic base or applying another feeder’s chute-removal sequence. If a part does not release as described, stop forcing it and use support for the actual unit.

Use the part-specific washing categories

Smart Feed removed parts and care
PartCurrent maker supportBoundary
Electronic baseDo not get the base wetKeep it separate from the removed washable components.
ConveyorHand-wash with warm soapy water, rinse and dryNot dishwasher safe.
Crumb catcherRemove from conveyor; hand-wash, rinse and dryNot dishwasher safe.
Hopper and lidMaker’s complete care chart/product list labels dishwasher safeRemove them; follow the actual unit’s instructions.
Bowl holder and bowlMaker’s chart/product list labels dishwasher safeTheir eligibility does not extend to the conveyor or base.

On a phone, scroll inside the table. Keyboard users can focus it and use the arrow keys.

The complete manufacturer chart was actually inspected: it labels hopper/lid, bowl holder and bowl dishwasher safe, while conveyor and crumb catcher are labelled for handwashing. The written cleaning page independently says the conveyor and crumb catcher are not dishwasher safe.

Rinse removed components well and dry them thoroughly before reassembly. The assembly page likewise directs warm soapy washing, rinsing and thorough drying prior to first use. A general dishwasher-safe product feature must not be read as permission to wash the whole unit.

Refit the catcher, belt lip and locking latch

  • Install the crumb catcher into the conveyor; the source notes it may already be fitted.
  • Align one belt lip with the side alignment arrows shown in the actual manufacturer illustration.
  • Insert the conveyor into the base. Push the red latch toward the front to close it, retaining the source’s snap/click locking indication.
  • Fit the hopper with the auger inside its hole, then latch both sides.
  • Insert the lid’s flat edge first and snap it in place. Refit the bowl holder and bowl as described.

Opening and closing are different latch actions. The written cleaning instruction pulls it back and upright to release; the written assembly instruction closes it toward the front. Their shared closing illustration is not evidence for an additional opening direction. [2]

The maker’s belt illustration highlights the lip and side arrow. It supplies no tooth count, torque value or calibration based on an invented belt position. Use the actual matching parts and leave uncertain fit with support.

Restore the food path and review actual output

After the parts are fully dry and properly refitted, use the model’s actual power and refill instructions. PetSafe’s separate amount guide directs priming after a refill; that guide keeps the manual FeedNow event separate from planned meals.

Review the intended schedule and the complete next relevant output. A closed latch establishes an assembly observation, not a measured meal. For continued alignment or dispensing problems, keep the model, removed-part condition, drying, refit and actual event record for PetSafe.

Two complete care decisions

Case 1

A fictional owner reads “dishwasher-safe parts” and places the conveyor, crumb catcher and base with the hopper. Which parts have been grouped incorrectly?

Show answer and explanation for case 1

The conveyor and crumb catcher are hand-wash-only under current support, while the base must not get wet.

The actual care chart gives named categories. Eligibility of the removed hopper and lid cannot be extended to the conveyor or the assembled electronic unit.

Case 2

In a fictional reassembly, the conveyor is dry but its belt lip has not been aligned to the side arrows. The owner assumes a latch click alone completes every step. What remains?

Show answer and explanation for case 2

Use the maker’s belt-lip alignment and then correctly seat and lock the conveyor as instructed.

Drying and locking are separate observations from the specified alignment. The example does not diagnose a fault or invent a new belt-tooth setting.

Sources and further reading

  1. How to Disassemble and Clean My PetSafe® Smart Feed Automatic Pet Feeder Complete current official main checked 16 November 2026. The selected maker illustrations were inspected separately; no device, account or feeding operation was performed.
  2. How to Assemble the PetSafe® Smart Feed Automatic Pet Feeder Complete current official main checked 16 November 2026. The selected maker illustrations were inspected separately; no device, account or feeding operation was performed.
  3. PetSafe Smart Feed model supportComplete current official main checked 16 November 2026. The selected maker illustrations were inspected separately; no device, account or feeding operation was performed.
  4. My PetSafe® Smart Feed Automatic Pet Feeder is Not Dispensing the Correct Amount of Food Complete current official main checked 16 November 2026; named counter/reset or refill-priming instructions.